Cool Galv Top Coat IR HR

Cool Galv Top Coat IR HR is an epoxy acrylic system that can be used as a finish coat for the Cool Galv system. It uses Infra-red Heat Reflective technology to reduce surface temperature and lower interior temperature.

Request Quote

[ht-ctc-chat call_to_action="Whatsapp Enquiry" pre_filled="Hello ,I would like to inquire on {{url}}" style=8]

Wishlist

Category: Cool Galv Tags: corrosion prevention, galvanishing, infrared protection, metal coating

Paints	Metal Paint, Exterior Paint, Surface Treatment
Size	1 Litre, 2 Litres, 5 Litres
Features	Corrosive Resistance, Solar Reflect, Weather Resistance
Colors	Grey

Description

Cool Galv is an advanced in-situ film galvanizing single-pack metallic coating, using ultra-fine atomized zinc dust that is treated with nanotechnology and complies with ASTM D520 type II. Cool-Galv provides 96% zinc content in dry film for long-term corrosion protection of steel thru cathodic protection and anti-rust treatment. The special resin used enable electrochemical bonding between zinc particle and metal surfaces.

COOL GALV TOP COAT IRHR has specially formulated an epoxy acrylic system to use as a finish coat for the Cool Galv system in case colorful finishing is required. It is using the latest near Infra-red Heat Reflective technology from the USA that can effectively reduce the surface temperature and lower the interior temperature for energy saving of air-conditioning and reduce carbon footprint.

Features

Good durability in a wide range of corrosive environments. Complied with ISO12944-6 C5I / C5M High Durability.
Easy to use – spray, brush, roller
Excellent adhesion properties to Cool Galv system
Effective, Reliable, and Cost Saving for assets maintenance.
Good weatherability.
Enable two coats duplex system for corrosion and cosmetics purposes.
Thin film IR Heat reflective technology to reduce the surface temperature and heat transfer into the building.

Typical Uses

As IR Heat Reflective finish coat for Cool Galv system for repair and maintenance of bare metal, damaged zinc substrate, and hot-dip galvanization. Anti-corrosion primer for steel structures such as internal and external of pipelines, silos, tanks, sheets of corrugated steel, fences, gates, bridges, bolts and nuts, containers, supports/trust, etc for industrial, construction, shipbuilding, and off-shore structures. Protection for welding seams, grating, metal sheets, and areas difficult to paint.

Physical Data

Colour	:	As specified
Flash Point	:	24 ⁰C
VOC	:	538g/L
Volume solid	:	45 +/- 2%
Gloss	:	Low Gloss

Shelf Life @ 25⁰C/indoor : 24 months

Typical Thickness: 50 ~ 80µ dried film.

Drying Time(at Dry Film Thickness 60µ)	Temperature	10⁰C	20⁰C	30⁰C
	Surface Dry	45mins	30mins	20 mins
	Hard Dry	3 hrs	1.5 hrs	1 hrs
Painting interval:	Minimum	3 hrs	1.5 hrs	1 hrs
Painting interval:	Max. (self)	–	–	–
Theoretical coverage (at DFT 40-80µ)		0.089~0.178 L/m²; 11.2~ 5.6 m²/L
Service temperature		-60 to 120⁰C (dry)

Application Data

Thinner: Hana Cool Galv Diluent

Application Method: airless spray, roller, brush

Mixing Procedure :	Mix for at least two minutes or until homogeneous.
Drying schedule :	Drying by solvent evaporation and moisture curing. Higher film thickness, insufficient ventilation, or lower temperature will require longer drying. Excessive humidity or condensation on the surface can interfere with the drying cause discoloration and may result in a surface haze.

This product requires the substrate temperature above the dew point ( + 3~5 ⁰ C). Condensation due to substrate temperatures below the dew point can cause flash rust on metal, affecting adhesion.

Application Procedure

Mix properly the paint before use.

Flush equipment with Cool Galv Diluent or Hana Thinner A before use.
Mix the paint thoroughly until homogeneous.
Thin with Cool Galv Diluent or HANA Thinner A only if necessary for workability.
When applying by conventional spray, use adequate air pressure and volume for proper atomization.
Apply a wet coat in even parallel passes, overlapping 50% to avoid holidays and pinholes.
Excessive thickness can prolong drying and sagging.
Clean up all equipment with thinner immediately after use.
Keep containers tightly close and store them in a proper storage area.

Condition of Application

Use a brush or roller with a 1/8″ nap. Apply at a sufficient thickness and avoid repeating rolling to have good leveling.

Temperature	:	Min 5 ⁰ C ; Max 50 ⁰ C
Humidity	:	Maximum 85 % R.H.
For Airless spray:-
Tip Size	:	Graco 721, 723 or equivalent
Paint Output pressure	:	11.7 – 17.7 MPa (g)
Viscosity	:	25 ~ 40 sec Ford Cup No 4
Thinning	:	0 – 10 % by volume

Surface Preparation

General :

Surfaces must be clean and dry, and all contaminants like dirt, dust, and oil must be removed by appropriate methods to ensure good adhesion.

Abrasive blast clean:

Abrasive blast clean to Sa 2.5 (ISO-8501) or SSPC-SP6. In case of hydro blasting or hydro jetting to remove the existing coating, ginger rust should be removed and blow dry before application. The surface profile must be a minimum of 50 microns.

Shop primed steelwork:

The Weld seam and the damaged area should be cleaned to a minimum St3 or SSPC-SP3. The shop-primed steelwork should be repaired for any rust and free from any contaminant with suitable secondary surface preparation such as spot blast, sweeping, or power tooling.

Aged Cool Galv Surface:

Remove zinc salt if any and any other contaminants prior to paint application.

Safety Precaution & Clean-Up

Safety :	Read and follow the material safety data sheet (MSDS) before use. Employ normal safety precautions. Put on necessary personal protection equipment when handling and using this product.
Ventilation :	when working in a confined workplace, thorough air ventilation must be used during and after application until the coating is cured. The ventilation system should be effective to prevent solvent vapor concentration from reaching a lower explosion limit for the product and to ensure exposure limit to the personnel is below the permissible exposure limit.
Caution :	All electrical equipment and installations should be made and properly grounded. In areas where explosion hazards exist, workmen should be used non-ferrous tools and conductive and non-sparkling shoes.
Clean-up :	Use Hana Paint polyurethane thinner (Hana Thinner U) or hydrocarbon solvent for cleaning. Observe safety precautions when using the solvents. In case of spillage, absorb and dispose of the material and used container according to local required regulations or through a licensed waste collector.

Disclaimer & Limited Warranty

Disclaimer

Data, specifications, directions, and recommendations given in this data sheet represent test results or experience obtained under controlled or specially defined circumstances. Their accuracy, completeness, or appropriateness under the actual conditions of any intended use is not guaranteed and must be determined by the user. The products are delivered and any technical assistance is given subject to our GENERAL CONDITIONS OF SALE, DELIVERY, AND SERVICE and, unless otherwise expressly agreed in writing, manufacturer and seller assume no liability in excess of that stated therein for results obtained, injury, direct or consequential damage incurred from the use as recommended above or otherwise.

Limited Warranty

Whilst we endeavor to ensure that all advice we give about this product is correct and manufactured according to the standard quality control system, however, we have no control over either the quality or condition of the substrate or many other factors affecting the use and application of the product. Therefore, unless we specifically agree in writing to do so, we do not accept any liability whatsoever or howsoever arising for the performance of the product or for any loss or damage arising out of the use of this product.

Need Help?

Send Us An Email

Contact us at info@awatrahana.com or call us at +60143989049 for questions related to this products or send us a form via the contact form below.

Your name Your email Contact No Product Enquire on Other Product

Subject Your message (optional)

Reviews

There are no reviews yet.

Be the first to review “Cool Galv Top Coat IR HR” Cancel reply

You must be logged in to post a review.

tel: +6010 231 7228

Available 9:00 - 18:00

info@awatrahana.com

Drop us a mail

Sign up for Newsletter